- 吸水率 [%]: 0.06
- 缺口沖擊強(qiáng)度: 0.214
- 斷裂伸長(zhǎng)率 [%]: 96.5
- 彎曲模量 [MPa]: 2.48
| Physical Properties | Metric | English | Comments | ||
|---|---|---|---|---|---|
| Specific Gravity | 1.44 g/cc | 1.44 g/cc | ASTM D792 | ||
| Water Absorption | 0.060 % | 0.060 % | Immersion, 24hr; ASTM D570(2) | ||
| Water Absorption at Saturation | 0.47 % | 0.47 % | Immersion; ASTM D570(2) | ||
| Mechanical Properties | Metric | English | Comments | ||
| Hardness, Rockwell M | 94 | 94 | ASTM D785 | ||
| Hardness, Shore D | 80 | 80 | ASTM D2240 | ||
| Tensile Strength | 72.4 MPa | 10500 psi | ASTM D638 | ||
| Elongation at Break | 5.0 % | 5.0 % | ASTM D638 | ||
| Tensile Modulus | 3.45 GPa | 500 ksi | ASTM D638 | ||
| Flexural Yield Strength | 96.5 MPa | 14000 psi | ASTM D790 | ||
| Flexural Modulus | 2.48 GPa | 360 ksi | ASTM D790 | ||
| Compressive Strength | 105.1 MPa | 15250 psi | 10% Def.; ASTM D695 | ||
| Compressive Modulus | 2.76 GPa | 400 ksi | ASTM D695 | ||
| Shear Strength | 58.6 MPa | 8500 psi | ASTM D732 | ||
| Izod Impact, Notched | 0.214 J/cm | 0.400 ft-lb/in | ASTM D256 Type A | ||
| Coefficient of Friction | 0.19 | 0.19 | Dry vs. Steel; QTM55007 | ||
| K (wear) Factor | 70.5 x 10-8 mm3/N-M | 35.0 x 10-10 in3-min/ft-lb-hr | QTM 55010 | ||
| Limiting Pressure Velocity | 0.210 MPa-m/sec | 6000 psi-ft/min | 4:1 safety factor; QTM 55007 | ||
| Electrical Properties | Metric | English | Comments | ||
| Surface Resistivity per Square | >= 1.00e+13 ohm | >= 1.00e+13 ohm | EOS/ESD S11.11 | ||
| Dielectric Constant | 3.6 @Frequency 1e+6 Hz | 3.6 @Frequency 1e+6 Hz | ASTM D150 | ||
| Dielectric Strength | 21.0 kV/mm | 533 kV/in | Short Term; ASTM D149 | ||
| Dissipation Factor | 0.020 @Frequency 1e+6 Hz | 0.020 @Frequency 1e+6 Hz | ASTM D150 | ||
| Thermal Properties | Metric | English | Comments | ||
| CTE, linear | 81.0 μm/m-°C @Temperature -40.0 - 149 °C | 45.0 μin/in-°F @Temperature -40.0 - 300 °F | ASTM E831 | ||
| Thermal Conductivity | 0.274 W/m-K | 1.90 BTU-in/hr-ft2-°F | ASTM F433 | ||
| Melting Point | 255 °C | 491 °F | Crystalline, Peak; ASTM D3418 | ||
| Maximum Service Temperature, Air | 98.9 °C | 210 °F | Long Term | ||
| Deflection Temperature at 1.8 MPa (264 psi) | 82.2 °C | 180 °F | ASTM D648 | ||
| Flammability, UL94 | HB | HB | 1/8 inch (Estimated Rating) | ||
| Compliance Properties | Metric | English | Comments | ||
| 3A-Dairy | Yes | Yes | |||
| Canada AG | No | No | |||
| FDA | Yes | Yes | |||
| NSF | No | No | |||
| USDA | Yes | Yes | |||
| USP Class VI | No | No | |||
| Chemical Resistance Properties | Metric | English | Comments | ||
| Acids, Strong (pH 1-3) | Limited | Limited | |||
| Acids, Weak | Acceptable | Acceptable | |||
| Alcohols | Acceptable | Acceptable | |||
| Alkalies, Strong (pH 11-14) | Unacceptable | Unacceptable | |||
| Alkalies, Weak | Acceptable | Acceptable | |||
| Chlorinated Solvents | Unacceptable | Unacceptable | |||
| Conductive / Static Dissipative | No | No | |||
| Continuous Sunlight | Limited | Limited | |||
| Hot Water / Steam | Limited | Limited | |||
| Hydrocarbons - Aliphatic | Acceptable | Acceptable | |||
| Hydrocarbons - Aromatic | Acceptable | Acceptable | |||
| Inorganic Salt Solutions | Acceptable | Acceptable | |||
| Ketones, Esters | Acceptable | Acceptable | |||
| Descriptive Properties | |||||
| Color | Gray | ||||
| Machinability | 2 | 1-10, 1=Easier to Machine | |||