- 密度 [g/cm3]: 1.51
- 吸水率 [%]: 0.19
- 缺口沖擊強度: 0.138
- 彎曲強度 [MPa]: 50.0
- 彎曲模量 [MPa]: 7.80
| Physical Properties | Metric | English | Comments |
|---|---|---|---|
| Bulk Density | 0.620 g/cc | 0.0224 lb/in3 | ASTM D1895 |
| Density | 1.51 g/cc | 0.0546 lb/in3 | ASTM D792 |
| Water Absorption | 0.19 % | 0.19 % | ASTM D570 |
| Linear Mold Shrinkage | 0.0073 cm/cm | 0.0073 in/in | ASTM D955 |
| Mechanical Properties | Metric | English | Comments |
| Hardness, Rockwell E | 79 | 79 | ASTM D785 |
| Tensile Strength, Ultimate | 50.0 MPa | 7250 psi | ASTM D638 |
| Elongation at Break | 0.70 % | 0.70 % | ASTM D638 |
| Tensile Modulus | 8.40 GPa | 1220 ksi | ASTM D638 |
| Flexural Strength | 79.0 MPa | 11500 psi | ASTM D790 |
| Flexural Modulus | 7.80 GPa | 1130 ksi | ASTM D790 |
| Compressive Strength | 182 MPa | 26400 psi | ASTM D695 |
| Poissons Ratio | 0.33 | 0.33 | ASTM D638 |
| Shear Modulus | 3.16 GPa | 458 ksi | Calculated |
| Izod Impact, Notched | 0.138 J/cm | 0.259 ft-lb/in | ASTM D256 |
| Charpy Impact, Notched | 0.153 J/cm2 | 0.728 ft-lb/in2 | ASTM D256 |
| Impact | 83 | 83 | J/m drop Ball Impact; PLENCO |
| Electrical Properties | Metric | English | Comments |
| Volume Resistivity | 1.70e+11 ohm-cm | 1.70e+11 ohm-cm | ASTM D247 |
| Dielectric Constant | 5.4 | 5.4 | ASTM D150 |
| Dielectric Strength | 7.20 kV/mm | 183 kV/in | Step by Step; ASTM D149 |
| 10.6 kV/mm | 269 kV/in | Short Time; ASTM D149 | |
| Dissipation Factor | 0.060 | 0.060 | ASTM D150 |
| Arc Resistance | 161 sec | 161 sec | ASTM D495 |
| Comparative Tracking Index | 175 V | 175 V | ASTM D3638 |
| Thermal Properties | Metric | English | Comments |
| CTE, linear | 44.0 μm/m-°C @Temperature 40.0 - 130 °C | 24.4 μin/in-°F @Temperature 104 - 266 °F | TMA; ASTM E831 |
| Maximum Service Temperature, Air | 202 °C | 396 °F | Heat Resistance; ASTM D570D |
| Deflection Temperature at 1.8 MPa (264 psi) | 173 °C | 343 °F | ASTM D648 |
| Flammability, UL94 | V-0 @Thickness 1.50 mm | V-0 @Thickness 0.0591 in | |
| Oxygen Index | 40 % | 40 % | ASTM D2863 |
| Shrinkage | 0.224 % | 0.224 % | 72 hr, 120oC; ASTM D1299 |