日韩av爽爽爽久久久久久,日韩深夜免费在线观看,国产精品久久久久久久专区,四虎库影成人在线播放,天堂va亚洲va欧美va国产

Momentive Performance Materials PF 31.5 Phenolic Formaldehyde Resin, Improved Electrical Properties

Momentive Performance Materials PF 31.5 Phenolic Formaldehyde Resin, Improved Electrical Properties 物性表: Momentive Performance Materials PF 31.5 Phenolic Formaldehyde Resin, Improved Electrical Properties物性表及特性介紹,Momentive Performance Materials PF 31.5 Phenolic Formaldehyde Resin, Improved Electrical Properties注塑參數詳情,如需Momentive Performance Materials PF 31.5 Phenolic Formaldehyde Resin, Improved Electrical Properties下載, 可到相關下載區下載

密度 [g/cm3]: 1.43
彎曲模量 [MPa]: 8.00

Physical Properties	Metric	English	Comments

Density	1.43 g/cc	0.0517 lb/in3	ISO 1183
Apparent Bulk Density	0.600 g/cc	0.0217 lb/in3	ISO 60
Linear Mold Shrinkage, Flow	0.0040 cm/cm	0.0040 in/in	Compression molding; ISO 2577
	0.0080 cm/cm	0.0080 in/in	Injection molding; ISO 2577

Mechanical Properties	Metric	English	Comments
Ball Indentation Hardness	300 MPa	43500 psi	H 961/30; ISO 2039/P1
Flexural Strength	115 MPa	16700 psi	2 mm/min; ISO 178
Flexural Modulus	8.00 GPa	1160 ksi	ISO 178
Charpy Impact Unnotched	0.800 J/cm2 @Temperature 23.0 °C	3.81 ft-lb/in2 @Temperature 73.4 °F	ISO 179-1/2 eU
Charpy Impact, Notched	0.150 J/cm2 @Temperature 23.0 °C	0.714 ft-lb/in2 @Temperature 73.4 °F	ISO 179-1/2 eA

Electrical Properties	Metric	English	Comments
Volume Resistivity	1.00e+12 ohm-cm	1.00e+12 ohm-cm	IEC 60093
Surface Resistance	1.00e+11 ohm	1.00e+11 ohm	IEC 60093
Dielectric Constant	6.0 @Frequency 100 Hz	6.0 @Frequency 100 Hz	IEC 60250
Dielectric Strength	30.0 kV/mm @Thickness 1.00 mm	762 kV/in @Thickness 0.0394 in	IEC 60243-P1
Dissipation Factor	0.10 @Frequency 100 Hz	0.10 @Frequency 100 Hz	IEC 60250
Comparative Tracking Index	125 V	125 V	Test liquid A; IEC 60112

Thermal Properties	Metric	English	Comments
Maximum Service Temperature, Air	140 °C	284 °F	<20000 hours; IEC 60216-P1
	180 °C	356 °F	< 50 hours; IEC 60216-P1
Deflection Temperature at 8.0 MPa	115 °C	239 °F	ISO 75-2
Shrinkage	0.50 %	0.50 %	Compression molding, 168 hours/110°C; ISO 2577
	1.0 %	1.0 %	Injection molding, 168 hours/110°C; ISO 2577

Processing Properties	Metric	English	Comments
Feed Temperature	60.0 - 75.0 °C	140 - 167 °F	Injection molding
Nozzle Temperature	80.0 - 100 °C	176 - 212 °F	Injection molding
Melt Temperature	80.0 - 100 °C	176 - 212 °F	Injection molding
Mold Temperature	160 - 190 °C	320 - 374 °F	Injection molding
	160 - 190 °C	320 - 374 °F	Compression molding
Injection Pressure	>= 15.0 MPa	>= 2180 psi	Compression and injection cavity mold pressure
Back Pressure	0.500 - 2.00 MPa	72.5 - 290 psi	Injection molding
Cure Time	0.167 - 0.333 min	0.00278 - 0.00556 hour	Per 1 mm of wall thickness, injection molding
	0.333 - 0.667 min	0.00556 - 0.0111 hour	Per 1 mm of wall thickness, compression molding

Descriptive Properties
Chromatic Spectrum	Subdued Colors
Creep Rupture Strength	Good
Holding Pressure	Approximately 40-60% of injection pressure
Media Resistance	Good
Moisture Absorption	35 mg		ISO 62, 24 hours at 23°C
Reserves by Peak Temperature	High
Thermal Expansion	Slight

關鍵詞:
供應
酚醛樹脂
Momentive Performance Materials PF 31.5 Phenolic Formaldehyde Resin
Improved Electrical Properties

轉載請注明: 轉自中國塑膠原料之家 http://www.spnmy.cn/wuxingbiao/

本文鏈接: http://www.spnmy.cn/yuanliaoku/show-34843.html

免責聲明: 本文 Momentive Performance Materials PF 31.5 Phenolic Formaldehyde Resin, Improved Electrical Properties 僅代表作者個人觀點，中國塑膠原料之家無關。中國塑膠原料之家網所轉載的內容，其版權均由原作者和資料提供方所擁有！如因作品版權問題需要處理，請與我們聯絡