- 缺口沖擊強(qiáng)度: 0.481
- 彎曲強(qiáng)度 [MPa]: 90.3
- 彎曲模量 [MPa]: 15.0
| Physical Properties | Metric | English | Comments |
|---|---|---|---|
| Specific Gravity | 1.84 g/cc | 1.84 g/cc | ASTM D792 |
| Water Absorption | <= 0.010 % | <= 0.010 % | 24 hours; ASTM D570 |
| Linear Mold Shrinkage, Flow | 0.00070 cm/cm | 0.00070 in/in | ASTM D955 |
| Linear Mold Shrinkage, Transverse | 0.0031 cm/cm | 0.0031 in/in | ASTM D955 |
| Mechanical Properties | Metric | English | Comments |
| Tensile Strength, Ultimate | 90.3 MPa | 13100 psi | ASTM D638 |
| Elongation at Break | 0.90 % | 0.90 % | ASTM D638 |
| Tensile Modulus | 16.1 GPa | 2330 ksi | ASTM D638 |
| Flexural Strength | 160 MPa | 23200 psi | ASTM D570 |
| Flexural Modulus | 15.0 GPa | 2170 ksi | ASTM D570 |
| Izod Impact, Notched | 0.481 J/cm | 0.900 ft-lb/in | ASTM D256 |
| Izod Impact Unnotched | 6.78 J | 5.00 ft-lb | ASTM D256 |
| Electrical Properties | Metric | English | Comments |
| Volume Resistivity | 1.80e+17 ohm-cm | 1.80e+17 ohm-cm | ASTM D257 |
| Surface Resistance | 1.50e+16 ohm | 1.50e+16 ohm | ASTM D257 |
| Dielectric Constant | 3.9 @Frequency 1e+6 Hz | 3.9 @Frequency 1e+6 Hz | ASTM D150 |
| 4.2 @Frequency 100 Hz | 4.2 @Frequency 100 Hz | ASTM D150 | |
| Dielectric Strength | 38.2 kV/mm @Thickness 1.60 mm | 970 kV/in @Thickness 0.0630 in | ASTM D149 |
| Dissipation Factor | 0.013 @Frequency 100 Hz | 0.013 @Frequency 100 Hz | ASTM D150 |
| 0.029 @Frequency 1e+6 Hz | 0.029 @Frequency 1e+6 Hz | ASTM D150 | |
| Thermal Properties | Metric | English | Comments |
| CTE, linear | 7.20 μm/m-°C @Temperature 20.0 °C | 4.00 μin/in-°F @Temperature 68.0 °F | Flow Direction; ASTM E831 |
| CTE, linear, Transverse to Flow | 59.4 μm/m-°C @Temperature 20.0 °C | 33.0 μin/in-°F @Temperature 68.0 °F | ASTM E831 |
| Deflection Temperature at 1.8 MPa (264 psi) | 278 °C | 532 °F | ASTM D648 |
| Flammability, UL94 | V-0 @Thickness 0.800 mm | V-0 @Thickness 0.0315 in | |
| Processing Properties | Metric | English | Comments |
| Melt Temperature | 321 - 360 °C | 610 - 680 °F | |
| Mold Temperature | 65.6 - 93.3 °C | 150 - 200 °F | |
| Drying Temperature | 149 °C | 300 °F | |
| Dry Time | 6 - 8 hour | 6 - 8 hour | |
| Dew Point | -28.9 °C | -20.0 °F | |