- 熔體流動速率 [g/10min]: 78.65
- 密度 [g/cm3]: 1.43
- 吸水率 [%]: 5.4
- 缺口沖擊強度: 12.0
- 拉伸強度 [MPa]: 135.0
- 彎曲模量 [MPa]: 7.40
| Physical Properties | Metric | English | Comments | ||
|---|---|---|---|---|---|
| Density | 1.43 g/cc | 0.0517 lb/in3 | ISO 1183 | ||
| Water Absorption | 5.4 - 6.0 % | 5.4 - 6.0 % | ISO 62 | ||
| Moisture Absorption at Equilibrium | 1.6 - 2.0 % | 1.6 - 2.0 % | (23°C/50% R.H.); ISO 62 | ||
| Viscosity Test | 140 cm3/g | 140 cm3/g | Viscosity number; ISO 307 | ||
| Melt Flow | 78.65 g/10 min @Load 5.00 kg, Temperature 275 °C | 78.65 g/10 min @Load 11.0 lb, Temperature 527 °F | ISO 527 | ||
| Mechanical Properties | Metric | English | Comments | ||
| Tensile Strength, Yield | 135 MPa | 19600 psi | 50mm/min; ISO 527 | ||
| Elongation at Yield | 4.6 % | 4.6 % | 50mm/min; ISO 527 | ||
| Modulus of Elasticity | 8.20 GPa | 1190 ksi | ISO 527 | ||
| Flexural Strength | 205 MPa | 29700 psi | ISO 178 | ||
| Flexural Modulus | 7.40 GPa | 1070 ksi | ISO 178 | ||
| Izod Impact, Notched (ISO) | 12.0 kJ/m2 | 5.71 ft-lb/in2 | ISO 180/A | ||
| Charpy Impact Unnotched | 10.5 J/cm2 | 50.0 ft-lb/in2 | ISO 179/1eU | ||
| Charpy Impact, Notched | 2.20 J/cm2 | 10.5 ft-lb/in2 | ISO 179/1eA | ||
| Electrical Properties | Metric | English | Comments | ||
| Volume Resistivity | 1.00e+8 ohm-cm | 1.00e+8 ohm-cm | IEC 60093 | ||
| Surface Resistance | 1.00e+10 ohm | 1.00e+10 ohm | IEC 60093 | ||
| Dielectric Constant | 6.0 @Frequency 1.00e+6 Hz | 6.0 @Frequency 1.00e+6 Hz | IEC 60250 | ||
| Dissipation Factor | 0.13 @Frequency 1.00e+6 Hz | 0.13 @Frequency 1.00e+6 Hz | IEC 60250 | ||
| Comparative Tracking Index | 550 V | 550 V | Test Solution A; IEC 60112 | ||
| Thermal Properties | Metric | English | Comments | ||
| Specific Heat Capacity | 1.40 J/g-°C | 0.335 BTU/lb-°F | |||
| Thermal Conductivity | 0.360 W/m-K | 2.50 BTU-in/hr-ft2-°F | DIN 52612 | ||
| Melting Point | 220 °C | 428 °F | DIN 53765 | ||
| Maximum Service Temperature, Air | 200 °C | 392 °F | |||
| Processing Properties | Metric | English | Comments | ||
| Melt Temperature | 270 - 290 °C | 518 - 554 °F | Injection-molding/Extrusion | ||
| Mold Temperature | 80.0 - 90.0 °C | 176 - 194 °F | Injection-molding | ||
| Descriptive Properties | |||||
| Color | BK00564 | ||||
| Commercial Status | North America and Europe | ||||
| Impact Modified | No | ||||
| Primary Processing Technique | Injection Molding | ||||