顆粒圖片：
包裝圖片：
成品圖片：
| Physical Properties | Metric | English | Comments | ||
|---|---|---|---|---|---|
| Specific Gravity | 1.15 g/cc | 1.15 g/cc | DAM; ASTM D792 | ||
| Density | 1.16 g/cc | 0.0419 lb/in³ | DAM; ISO 1183 | ||
| Water Absorption | 1.8 % @Temperature 23.0 °C |
1.8 % @Temperature 73.4 °F |
Immersion 24h; DAM; ISO 62, Similar to | ||
| Linear Mold Shrinkage | 0.0080 cm/cm @Thickness 1.60 mm |
0.0080 in/in @Thickness 0.0630 in |
Flow; DAM | ||
| 0.0080 cm/cm @Thickness 1.60 mm |
0.0080 in/in @Thickness 0.0630 in |
Transverse; DAM | |||
| 0.011 cm/cm @Thickness 3.20 mm |
0.011 in/in @Thickness 0.126 in |
Flow; DAM | |||
| 0.011 cm/cm @Thickness 3.20 mm |
0.011 in/in @Thickness 0.126 in |
Transverse; DAM | |||
| Linear Mold Shrinkage, Flow | 0.0090 cm/cm @Thickness 2.00 mm |
0.0090 in/in @Thickness 0.0787 in |
DAM; ISO 294-4 | ||
| Linear Mold Shrinkage, Transverse | 0.010 cm/cm @Thickness 2.00 mm |
0.010 in/in @Thickness 0.0787 in |
DAM; ISO 294-4 | ||
| Mechanical Properties | Metric | English | Comments | ||
| Tensile Strength at Break | 80.0 MPa @Temperature 23.0 °C |
11600 psi @Temperature 73.4 °F |
DAM; ISO 527 | ||
| Tensile Strength | 89.6 MPa @Temperature 23.0 °C |
13000 psi @Temperature 73.4 °F |
DAM; ASTM D638 | ||
| Tensile Strength, Yield | 90.0 MPa @Temperature 23.0 °C |
13100 psi @Temperature 73.4 °F |
50mm/min; DAM; ISO 527 | ||
| Elongation at Break | 10 % @Temperature 23.0 °C |
10 % @Temperature 73.4 °F |
DAM; nominal; ISO 527 | ||
| 10 % @Temperature 23.0 °C |
10 % @Temperature 73.4 °F |
DAM; ISO 527 | |||
| 14 % @Temperature 23.0 °C |
14 % @Temperature 73.4 °F |
DAM; ASTM D638 | |||
| Elongation at Yield | 4.0 % @Temperature 23.0 °C |
4.0 % @Temperature 73.4 °F |
50mm/min; DAM; ISO 527 | ||
| Tensile Modulus | 3.75 GPa @Temperature 23.0 °C |
544 ksi @Temperature 73.4 °F |
DAM; ISO 527 | ||
| Flexural Modulus | 3.45 GPa @Temperature 23.0 °C |
500 ksi @Temperature 73.4 °F |
DAM; ASTM D790 | ||
| 3.66 GPa @Temperature 23.0 °C |
531 ksi @Temperature 73.4 °F |
DAM; ISO 178 | |||
| Izod Impact, Notched | 0.430 J/cm @Temperature 23.0 °C |
0.806 ft-lb/in @Temperature 73.4 °F |
DAM; ASTM D256 | ||
| Charpy Impact Unnotched | 13.5 J/cm² @Temperature 23.0 °C |
64.2 ft-lb/in² @Temperature 73.4 °F |
DAM; ISO 179/1eU | ||
| Charpy Impact, Notched | 0.300 J/cm² @Temperature -40.0 °C |
1.43 ft-lb/in² @Temperature -40.0 °F |
DAM; ISO 179/1eA | ||
| 0.370 J/cm² @Temperature 23.0 °C |
1.76 ft-lb/in² @Temperature 73.4 °F |
DAM; ISO 179/1eA | |||
| Electrical Properties | Metric | English | Comments | ||
| Comparative Tracking Index | >= 600 V | >= 600 V | DAM; IEC 60112 | ||
| >= 600 V @Thickness 3.00 mm, Temperature 23.0 °C |
>= 600 V @Thickness 0.118 in, Temperature 73.4 °F |
DAM; UL 746A | |||
| Thermal Properties | Metric | English | Comments | ||
| Melting Point | 260 °C | 500 °F | 10°C/min; DAM; ISO 11357-1/-3 | ||
| 264 °C | 507 °F | DAM; ASTM D3418 | |||
| Deflection Temperature at 0.46 MPa (66 psi) | 230 °C | 446 °F | DAM; ASTM D648 | ||
| 235 °C | 455 °F | DAM; ISO 75-1/-2 | |||
| Deflection Temperature at 1.8 MPa (264 psi) | 70.0 °C | 158 °F | DAM; ASTM D648 | ||
| 84.0 °C | 183 °F | DAM; ISO 75-1/-2 | |||
| UL RTI, Electrical | 130 °C @Thickness 1.50 mm |
266 °F @Thickness 0.0591 in |
DAM; UL 746B | ||
| 130 °C @Thickness 3.00 mm |
266 °F @Thickness 0.118 in |
DAM; UL 746B | |||
| 130 °C @Thickness 0.750 mm |
266 °F @Thickness 0.0295 in |
DAM; UL 746B | |||
| UL RTI, Mechanical with Impact | 75.0 °C @Thickness 0.750 mm |
167 °F @Thickness 0.0295 in |
DAM; UL 746B | ||
| 75.0 °C @Thickness 1.50 mm |
167 °F @Thickness 0.0591 in |
DAM; UL 746B | |||
| 75.0 °C @Thickness 3.00 mm |
167 °F @Thickness 0.118 in |
DAM; UL 746B | |||
| UL RTI, Mechanical without Impact | 85.0 °C @Thickness 0.750 mm |
185 °F @Thickness 0.0295 in |
DAM; UL 746B | ||
| 85.0 °C @Thickness 1.50 mm |
185 °F @Thickness 0.0591 in |
DAM; UL 746B | |||
| 85.0 °C @Thickness 3.00 mm |
185 °F @Thickness 0.118 in |
DAM; UL 746B | |||
| Flammability, UL94 | V-0 @Thickness 0.750 mm |
V-0 @Thickness 0.0295 in |
DAM; IEC 60695-11-10 | ||
| V-0 @Thickness 1.50 mm |
V-0 @Thickness 0.0591 in |
DAM; IEC 60695-11-10 | |||
| V-0 @Thickness 3.00 mm |
V-0 @Thickness 0.118 in |
DAM; IEC 60695-11-10 | |||
| V-0 @Thickness 3.00 mm |
V-0 @Thickness 0.118 in |
DAM; UL94 | |||
| V-0 @Thickness 0.750 mm |
V-0 @Thickness 0.0295 in |
DAM; UL94 | |||
| V-0 @Thickness 1.50 mm |
V-0 @Thickness 0.0591 in |
DAM; UL94 | |||
| Glow Wire Test | 775 °C @Thickness 3.00 mm |
1430 °F @Thickness 0.118 in |
DAM; Ignition; IEC 60695-2-13 | ||
| 775 °C @Thickness 1.50 mm |
1430 °F @Thickness 0.0591 in |
DAM; Ignition; IEC 60695-2-13 | |||
| 960 °C @Thickness 1.50 mm |
1760 °F @Thickness 0.0591 in |
DAM; IEC 60695-2-12 | |||
| 960 °C @Thickness 3.00 mm |
1760 °F @Thickness 0.118 in |
DAM; IEC 60695-2-12 | |||
| Processing Properties | Metric | English | Comments | ||
| Melt Temperature | 280 °C | 536 °F | DAM; Optimum | ||
| 270 - 290 °C | 518 - 554 °F | DAM | |||
| Mold Temperature | 70.0 °C | 158 °F | DAM; optimum | ||
| 50.0 - 90.0 °C | 122 - 194 °F | DAM | |||
| Drying Temperature | 80.0 °C | 176 °F | DAM | ||
| Dry Time | 2.00 - 4.00 hour | 2.00 - 4.00 hour | DAM | ||
| Moisture Content | <= 0.20 % | <= 0.20 % | DAM | ||
| De |
|||||
| Additive | Flame Retardant | DAM | |||
| Lubricant | DAM | ||||
| Appearance | Natural Color | DAM | |||
| Contains Flame Retardant | Yes | DAM | |||
| Drying Recommended | Yes, if moisture content of resin exceeds recommended level | DAM | |||
| Features | Crystalline, Semi | DAM | |||
| Flame Retardant | DAM | ||||
| Nucleated | DAM | ||||
| Processability, Good | DAM | ||||
| Flame Retardant - Halogen/Red Phosphorus Free | Yes | DAM | |||
| Forms | Pellets | DAM | |||
| Generic | Nylon 66 | DAM | |||
| Heat Stabilized | Yes | DAM | |||
| Material Status | Current | DAM | |||
| Part Marking Code | >PA66-FR(30)< | ISO 11469; DAM | |||
| Polymer Family | Polyamide | DAM | |||
| Polymer Type | PA66 | DAM | |||
| Processing Method | Injection Molding | DAM | |||
| Product Category | Flame Retardant Resins | DAM | |||
| Unreinforced Resins | DAM | ||||
| Region Available - Global | Yes | DAM | |||
| Resin Identification | PA66-FR(30) | ISO 1043; DAM | |||
| RoHS Compliance | Contact Manufacturer | DAM | |||
| Ultrasonic Weldable | Yes | DAM | |||
| Uses | Connectors | DAM | |||
| Electrical Parts | DAM | ||||
| Electrical/Electronic Applications | DAM | ||||
概述
PA塑料(尼龍，聚酰胺)，英文名稱:Polyamide
PA的品種繁多，有PA6、PA66、PAll、PAl2、PA46、PA610、PA612、PAl010等，以及近幾年開發的半芳香族尼龍PA6T和特種尼龍等很多新品種。
物理性能
比重：PA6 1.14克/立方厘米，PA66 1.15克/立方厘米，PA1010 1.05克/立方厘米
成型收縮率：PA6 0.8-2.5% ，PA66 1.5-2.2%
成型溫度：220-300℃
干燥條件：100-110℃/12小時
堅韌、耐磨、耐油、,耐水、抗酶菌、但吸水大
燃燒鑒別方法：火焰上端黃色，下端藍色，燃燒后塑料熔滴落，起泡，離火后特殊的羊毛，指甲燒焦味和帶芹菜味
|
尼龍6： |
彈性好，沖擊強度，吸水較大 |
|
尼龍66： |
性能優于尼龍6，強度高，耐磨性好 |
|
尼龍610： |
與尼龍66相似，但吸水小，剛度低 |
|
尼龍1010： |
半透明，吸水小。耐寒性較好。適于制作一般機械零件、減磨耐磨零件、傳動零件以及化工、電器、儀表等零件 |
成型性能
1、結晶料，熔點較高，熔融溫度范圍窄，熱穩定性差，料溫超過300度、滯留時間超過30分鐘即分解。較易吸濕，需干燥，含水量不得超過0.3%。
2、流動性好，易溢料。宜用自鎖時噴嘴，并應加熱。
3、成型收縮范圍及收縮率大，方向性明顯，易發生縮孔、變形等。
4、模溫按塑件壁厚在20～90度范圍內選取，注射壓力按注射機類型、料溫、塑件形狀尺寸、模具澆注系統選定，成型周期按塑件壁厚選定。樹脂粘度小時，注射、冷卻時間應取長，并用白油作脫模劑。
5、模具澆注系統的形式和尺寸，增大流道和澆口尺寸可減少縮水。
聚酰胺的不足之處在于：由于熱膨脹和吸水性所至的尺寸精度不夠，耐酸性差，硬度和彈性模量不夠。經改良以后，也是比較優秀的工程塑料之一。
應用
汽車制造方面
用于制造燃料濾網、燃料過濾器、罐、捕集器、儲油槽、發動機汽缸蓋罩、散熱器水缸、平衡旋轉軸齒輪。也可用在汽車的電器配件、接線柱等。另外，它還可用作驅動、控制部件等。
電器電子工業
可用于制造電飯鍋、電動吸塵器、高頻電子食品加熱器，電器產品的接線柱、開關和電阻器等。
醫療器械儀器
用于醫用輸血管、取血器、輸液器等。PA單絲可做外科手術縫線、假發等；另外，電子打字機的數字旋轉盤、接線柱、傳動齒輪、印刷機的帶式過濾片等。
其它方面
用于制作一次性打火機體、堿性干電池襯墊，摩托車駕駛員的頭盔，辦公機器外殼，辦公用椅的角輪、座和靠背，冰鞋、釣魚線等，PA薄膜氣體阻隔性能優良，而且耐油性、耐低溫沖擊性、耐穿透性好，可用于肉、火腿腸等冷凍食品的包裝。聚酰胺還可棒材和板材，也作齒輪或其它傳動裝置。
上海浩銘塑膠有限公司！本公司承諾，所有產品都是原廠家，原包裝一線獨家營銷！
可提供以下報告：COA（產地證明）SGS（檢測報告）MSDS（成分報告）FDA（食品安全報告）UL黃卡（出口報告）正規發票！歡迎新老客戶來電咨詢：
聯系人：鄧小姐
聯系電話：13917657923
聯系QQ:996152797
聯系郵箱：996152797@qq.com