永久免费av无码网站直播,五月天免费中文字幕av,日本亚洲色大成网站www久久,97亚洲熟妇自偷自拍另类图片,暖暖免费观看电视在线高清

UBE UBESTA? 3030U Nylon 12 (After Hydrochloric Acid (10%) for 500 hours)

UBE UBESTA? 3030U Nylon 12 (After Hydrochloric Acid (10%) for 500 hours) 物性表: UBE UBESTA? 3030U Nylon 12 (After Hydrochloric Acid (10%) for 500 hours)物性表及特性介紹,UBE UBESTA? 3030U Nylon 12 (After Hydrochloric Acid (10%) for 500 hours)注塑參數詳情,如需UBE UBESTA? 3030U Nylon 12 (After Hydrochloric Acid (10%) for 500 hours)下載, 可到相關下載區下載

拉伸強度 [MPa]: 35.4

Mechanical Properties	Metric	English	Comments

Tensile Strength at Break	46.9 MPa	6800 psi	93% Ret.
Tensile Strength, Yield	35.4 MPa	5130 psi	84% Ret.
Elongation at Break	97 %	97 %	121% Ret.

Processing Properties	Metric	English	Comments
Processing Temperature	230 °C	446 °F	Flange Temperature for T-Die Cast Film Extrusion
Zone 1	190 °C	374 °F	For T-Die Cast Film Extrusion
	230 °C	446 °F	For 8x1 mm Tube Extrusion
Zone 2	210 °C	410 °F	For T-Die Cast Film Extrusion
	225 °C	437 °F	For 8x1 mm Tube Extrusion
Zone 3	220 °C	428 °F	For 8x1 mm Tube Extrusion
	230 °C	446 °F	For T-Die Cast Film Extrusion
Zone 4	215 °C	419 °F	For 8x1 mm Tube Extrusion
Die Temperature	230 °C	446 °F	For T-Die Cast Film Extrusion
Die Opening	0.0400 cm	0.0157 in	For T-Die Cast Film Extrusion
Roll Temperature	50.0 °C	122 °F	Chill Roll Temperature for T-Die Cast Film Extrusion
Drying Temperature	80.0 °C	176 °F	Option 1
	100 °C	212 °F	Option 2
	110 °C	230 °F	Option 3
Dry Time	2 - 4 hour	2 - 4 hour	Option 3
	4 - 6 hour	4 - 6 hour	Option 2
	6 - 8 hour	6 - 8 hour	Option 1
Screw Speed	15 - 76 rpm	15 - 76 rpm	For 8x1 mm Tube Extrusion

Descriptive Properties
C/R	3-3.5:1		For 8x1 mm Tube Extrusion
Calibrating Vacuum	100 mbar		For 8x1 mm Tube Extrusion
Calibration	9.95 mm		For 8x1 mm Tube Extrusion
Compression Ratio	min 3:1		For 8x1 mm Tube Extrusion
Die Diameter	16 mm		For 8x1 mm Tube Extrusion
Die Width	300 mm		For T-Die Cast Film Extrusion
Extruder	Barmag, Screw Diameter = 30 mm		For T-Die Cast Film Extrusion
Extruder Characteristics	65 mm screw diameter		For 8x1 mm Tube Extrusion
Film Thickness	60 microns		For T-Die Cast Film Extrusion
Haul Off Speed	5 m/min		For T-Die Cast Film Extrusion
Haul Speed	10-55 m/min		For 8x1 mm Tube Extrusion
L/D Ratio	25:1		For 8x1 mm Tube Extrusion
Length of Compression Zone	30% of screw length		For 8x1 mm Tube Extrusion
Length of Feeding Zone	30-40% of screw length		For 8x1 mm Tube Extrusion
Length of Metering Zone	30-45% of screw length		For 8x1 mm Tube Extrusion
Mandrel Diameter	12 mm		For 8x1 mm Tube Extrusion
Tensile Work To Break	912 kJ/m²		112% Ret.
Water Temperature	10-18°C		For 8x1 mm Tube Extrusion

關鍵詞:
供應
PA12
UBE UBESTA? 3030U Nylon 12 (After Hydrochloric Acid (10%) for 500 hours)

轉載請注明: 轉自中國塑膠原料之家 http://www.spnmy.cn/wuxingbiao/

本文鏈接: http://www.spnmy.cn/yuanliaoku/show-47271.html

免責聲明: 本文 UBE UBESTA? 3030U Nylon 12 (After Hydrochloric Acid (10%) for 500 hours) 僅代表作者個人觀點，中國塑膠原料之家無關。中國塑膠原料之家網所轉載的內容，其版權均由原作者和資料提供方所擁有！如因作品版權問題需要處理，請與我們聯絡