- 吸水率 [%]: 0.1
- 缺口沖擊強度: 0.481
- 斷裂伸長率 [%]: 15.2
- 彎曲模量 [MPa]: 3.45
- 硬度: 55.0
| Physical Properties | Metric | English | Comments | ||
|---|---|---|---|---|---|
| Specific Gravity | 2.32 g/cc | 2.32 g/cc | ASTM D792 | ||
| Water Absorption | 0.10 % | 0.10 % | Immersion, 24hr; ASTM D570(2) | ||
| Water Absorption at Saturation | 0.30 % | 0.30 % | Immersion; ASTM D570(2) | ||
| Deformation | 5.0 % | 5.0 % | 2000 psi; 122°F (50°C) | ||
| Mechanical Properties | Metric | English | Comments | ||
| Hardness, Rockwell R | 55 | 55 | ASTM D785 | ||
| Hardness, Shore D | 70 | 70 | ASTM D2240 | ||
| Tensile Strength | 7.58 MPa | 1100 psi | ASTM D638 | ||
| Elongation at Break | 30 % | 30 % | ASTM D638 | ||
| Tensile Modulus | 2.07 GPa | 300 ksi | ASTM D638 | ||
| Flexural Yield Strength | 15.2 MPa | 2200 psi | ASTM D790 | ||
| Flexural Modulus | 3.45 GPa | 500 ksi | ASTM D790 | ||
| Compressive Strength | 27.6 MPa | 4000 psi | 10% Def.; ASTM D695 | ||
| Compressive Modulus | 1.72 GPa | 250 ksi | ASTM D695 | ||
| Shear Strength | 14.5 MPa | 2100 psi | ASTM D732 | ||
| Izod Impact, Notched | 0.481 J/cm | 0.900 ft-lb/in | ASTM D256 Type A | ||
| Coefficient of Friction | 0.15 | 0.15 | Dry vs. Steel; QTM55007 | ||
| K (wear) Factor | 1210 x 10-8 mm3/N-M | 600 x 10-10 in3-min/ft-lb-hr | QTM 55010 | ||
| Limiting Pressure Velocity | 0.280 MPa-m/sec | 8000 psi-ft/min | 4:1 safety factor; QTM 55007 | ||
| Electrical Properties | Metric | English | Comments | ||
| Surface Resistivity per Square | >= 1.00e+13 ohm | >= 1.00e+13 ohm | EOS/ESD S11.11 | ||
| Dielectric Constant | 2.85 @Frequency 1e+6 Hz | 2.85 @Frequency 1e+6 Hz | ASTM D150 | ||
| Dielectric Strength | 10.8 kV/mm | 275 kV/in | Short Term; ASTM D149 | ||
| Dissipation Factor | 0.0080 @Frequency 1e+6 Hz | 0.0080 @Frequency 1e+6 Hz | ASTM D150 | ||
| Thermal Properties | Metric | English | Comments | ||
| CTE, linear | 45.0 μm/m-°C @Temperature -40.0 - 149 °C | 25.0 μin/in-°F @Temperature -40.0 - 300 °F | ASTM E831 | ||
| Thermal Conductivity | 0.764 W/m-K | 5.30 BTU-in/hr-ft2-°F | ASTM F433 | ||
| Melting Point | 327 °C | 621 °F | Crystalline, Peak; ASTM D3418 | ||
| Maximum Service Temperature, Air | 260 °C | 500 °F | Long Term | ||
| Deflection Temperature at 1.8 MPa (264 psi) | 132 °C | 270 °F | ASTM D648 | ||
| Flammability, UL94 | V-0 | V-0 | 1/8 inch (Estimated Rating) | ||
| Compliance Properties | Metric | English | Comments | ||
| 3A-Dairy | No | No | |||
| Canada AG | No | No | |||
| FDA | No | No | |||
| NSF | No | No | |||
| USDA | No | No | |||
| USP Class VI | No | No | |||
| Chemical Resistance Properties | Metric | English | Comments | ||
| Acids, Strong (pH 1-3) | Acceptable | Acceptable | |||
| Acids, Weak | Acceptable | Acceptable | |||
| Alcohols | Acceptable | Acceptable | |||
| Alkalies, Strong (pH 11-14) | Unacceptable | Unacceptable | |||
| Alkalies, Weak | Acceptable | Acceptable | |||
| Chlorinated Solvents | Acceptable | Acceptable | |||
| Conductive / Static Dissipative | No | No | |||
| Continuous Sunlight | Acceptable | Acceptable | |||
| Hot Water / Steam | Limited | Limited | |||
| Hydrocarbons - Aliphatic | Acceptable | Acceptable | |||
| Hydrocarbons - Aromatic | Acceptable | Acceptable | |||
| Inorganic Salt Solutions | Acceptable | Acceptable | |||
| Ketones, Esters | Acceptable | Acceptable | |||
| Descriptive Properties | |||||
| Color | Natural | ||||
| Machinability | 2 | 1-10, 1=Easier to Machine | |||