精品人妻少妇一区二区三区,精品无码久久久久国产电影,久久精品国产亚洲av忘忧草18,久久天天躁夜夜躁狠狠,久久精品伊人波多野结衣

HOSTAFORM C 9021 AS|POM|Ticona

HOSTAFORM C 9021 AS|POM|Ticona 物性表: HOSTAFORM C 9021 AS|POM|Ticona物性表及特性介紹,HOSTAFORM C 9021 AS|POM|Ticona注塑參數詳情,如需HOSTAFORM C 9021 AS|POM|Ticona下載, 可到相關下載區下載

Product TextsPOM copolymerPlease refer to 5	cm3/10min	ISO 1133
溫度(Temperature)	190	°C	ISO 1133
負載(Load)	2.16	kg	ISO 1133
成型收縮(Molding shrinkage) (parallel)	1.9	%	ISO 294-4, 2577
成型收縮(Molding shrinkage) (normal)	1.8	%	ISO 294-4, 2577

機械性能(機械性能(Mechanical properties))	值(Value)	單位(Unit)	測試標準(Test Standard)
ISO數據(ISO數據(CAMPUS/ISO) Data)
拉伸模量(Tensile Modulus)	2750	MPa	ISO 527-1/-2
屈服應力(Yield stress)	63	MPa	ISO 527-1/-2
屈服應變(Yield strain)	10	%	ISO 527-1/-2
斷裂拉伸應變(Nominal strain at break)	30	%	ISO 527-1/-2
簡支梁沖擊強度(Charpy impact strength) (+23°C)	180	kJ/m2	ISO 179/1eU
簡支梁沖擊強度(Charpy impact strength) (-30°C)	180	kJ/m2	ISO 179/1eU
簡支梁缺口沖擊強度(Charpy notched impact strength) (+23°C)	6	kJ/m2	ISO 179/1eA
簡支梁缺口沖擊強度(Charpy notched impact strength) (-30°C)	5.5	kJ/m2	ISO 179/1eA

熱性能(熱性能(Thermal properties))	值(Value)	單位(Unit)	測試標準(Test Standard)
ISO數據(ISO數據(CAMPUS/ISO) Data)
熔化溫度(熔化溫度(Melting temperature)) (10°C/min)	166	°C	ISO 11357-1/-3
COEFF線性熱(Coeff. of linear therm. expansion) (parallel)	110	E-6/K	ISO 11359-1/-2

電氣性能(Electrical properties)	值(Value)	單位(Unit)	測試標準(Test Standard)
ISO數據(ISO數據(CAMPUS/ISO) Data)
表面電阻率(Surface resistivity)	1E12	Ohm	IEC 60093

其他屬性(Other properties)	值(Value)	單位(Unit)	測試標準(Test Standard)
ISO數據(ISO數據(CAMPUS/ISO) Data)
密度(Density)	1410	kg/m3	ISO 1183

Test specimen production	值(Value)	單位(Unit)	測試標準(Test Standard)
ISO數據(ISO數據(CAMPUS/ISO) Data)
Processing conditions acc. ISO	9990	-	ISO ....-2
Injection Molding, melt temperature	205	°C	ISO 294
Injection Molding, mold temperature	90	°C	ISO 10724
Injection Molding, injection velocity	200	mm/s	ISO 294
Injection Molding, pressure at hold	90	MPa	ISO 294

CharacteristicsProcessingInjection MoldingDelivery formPelletsAdditivesRelease agentSpecial CharacteristicsAnti-staticRegional AvailabilityNorth America, Europe, Asia PacificOther text informationInjection moldingPREPROCESSING 40 mm Water content 0,2%g. moisturizing is not necessary.DisclaimerCopyright M-Base Engineering+Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from M-Base; this is especially valid for claims of compensation resulting from consequential damages. M-Base explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
[/td][/tr][/table]

關鍵詞:
HOSTAFORM C 9021 AS|POM|Ticona