色婷婷综合久久久久中文字幕 ,在线观看热码亚洲av每日更新,夜夜爽免费888视频,国产乱码精品一区二三区,国产另类在线欧美日韩

Product TextsCelcon? acetal copolymer grade M15HPis a creep resistant, high 3	cm3/10min	ISO 1133
溫度(Temperature)	190	°C	ISO 1133
負載(Load)	2.16	kg	ISO 1133
成型收縮(Molding shrinkage) (parallel)	2.3	%	ISO 294-4, 2577
成型收縮(Molding shrinkage) (normal)	1.9	%	ISO 294-4, 2577

機械性能(機械性能(Mechanical properties))	值(Value)	單位(Unit)	測試標準(Test Standard)
ISO數據(ISO數據(CAMPUS/ISO) Data)
拉伸模量(Tensile Modulus)	2800	MPa	ISO 527-1/-2
簡支梁沖擊強度(Charpy impact strength) (+23°C)	280	kJ/m2	ISO 179/1eU
簡支梁沖擊強度(Charpy impact strength) (-30°C)	235	kJ/m2	ISO 179/1eU
簡支梁缺口沖擊強度(Charpy notched impact strength) (+23°C)	11	kJ/m2	ISO 179/1eA
簡支梁缺口沖擊強度(Charpy notched impact strength) (-30°C)	8.5	kJ/m2	ISO 179/1eA

熱性能(熱性能(Thermal properties))	值(Value)	單位(Unit)	測試標準(Test Standard)
ISO數據(ISO數據(CAMPUS/ISO) Data)
熔化溫度(熔化溫度(Melting temperature)) (10°C/min)	173	°C	ISO 11357-1/-3
溫度負荷變形(Temp. of deflection under load) (1.80 MPa)	101	°C	ISO 75-1/-2
溫度負荷變形(Temp. of deflection under load) (0.45 MPa)	158	°C	ISO 75-1/-2
維卡軟化溫度（50℃/ h的50N）Vicat softening temperature	166	°C	ISO 306
COEFF線性熱(Coeff. of linear therm. expansion) (parallel)	110	E-6/K	ISO 11359-1/-2
COEFF線性熱(Coeff. of linear therm. expansion) (normal)	120	E-6/K	ISO 11359-1/-2

其他屬性(Other properties)	值(Value)	單位(Unit)	測試標準(Test Standard)
ISO數據(ISO數據(CAMPUS/ISO) Data)
吸水率(Water absorption)	0.75	%	Sim. to ISO 62
吸濕性(Humidity absorption)	0.2	%	Sim. to ISO 62
密度(Density)	1400	kg/m3	ISO 1183

流變計算屬性(Rheological calculation properties)	值(Value)	單位(Unit)	測試標準(Test Standard)
ISO數據(ISO數據(CAMPUS/ISO) Data)
密度(Density) of melt	1170	kg/m3	-

Test specimen production	值(Value)	單位(Unit)	測試標準(Test Standard)
ISO數據(ISO數據(CAMPUS/ISO) Data)
Processing conditions acc. ISO	9990	-	ISO ....-2
Injection Molding, melt temperature	210	°C	ISO 294
Injection Molding, mold temperature	100	°C	ISO 10724
Injection Molding, injection velocity	140	mm/s	ISO 294
Injection Molding, pressure at hold	86	MPa	ISO 294

Diagrams Excessive moisture can lead to splay For better uniformity in molding Desiccant water content = 0.35%.35 Mpa/50 PSI) are favored. Using a low compression screw e.-general purpose with a 2:1 compression ratio) can result in Using a high back 5 mm (0.060 in.). Wall ) may use a cooler (82 C/180 F) ) may use In general, mold It may be Film extrusionPREPROCESSING For at 80 C (180 F). Desiccant hopper dryers are not Max. moisture content = 0. The screw should be a high compression ratio of at least The Profile extrusionPREPROCESSING For at 80 C (180 F). Desiccant hopper dryers are not Max. moisture content = 0.035% The screw should be a high compression ratio of at least The For thick walled ), annealing is recommended to reduce CalanderingPREPROCESSINGCompression moldingPREPROCESSINGDisclaimerCopyright M-Base Engineering+Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from M-Base; this is especially valid for claims of compensation resulting from consequential damages. M-Base explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
[/td][/tr][/table]

CELCON M15HP|POM|Ticona